NC Data Recorder
DR-Pro S can send and receive CNC data with SD and SDHC memory cards.
Data stored to a SD card is the format only for NC. You can't generate or edit the data on your computer.
※DR-Pro S works only in SPI mode.
CPRM is not used.
- Receive NC data
- Send NC data
- Store NC data
- Display NC data
- Able to set a wide variety of parameters
- Able to display SD card's information
- Compact and light-weight
DR-Pro S is equipped with a rechargeable battery in its compact body. You can bring and use it wherever you go.
- Super high-speed communication
DR-Pro S can send and reveive a large amount of program data at super high speed.
It transmits and reveives data for 3,800 words per second at most.
(DR-Pro S can conduct data transmission at the above transmission rate when the device connected to DR-Pro S has the same data transfer capacity as DR-Pro S)
- Supporting SD and SDHC cards
DR-Pro S is equipped with a slot for an SD card (Storage from 8M to 2G) and SDHC card (Storage from 4G to 32G). With SD and SDHC cards, DR-Pro S can transmit and receive a large amount of program data. (Mini-SD and Micro-SD cards can be usable with a card reader) *1.
Data can be directly transmitted to/from a computer supporting SD and SDHC cards *2.
*1 SDXC card is not supported.
*2 Data can't be editted.
- Automatic operation mode
You can control DR-Pro S from a CNC machine side remotely. DR-Pro S can almost automatically perform data transmission.
(Automatic mode is only for CNC and CAM machines supporting DC control code output)
- Manual mode
DR-Pro S has manual mode. Manual mode allows you to transmit data in a variety of communication methods. It also allows you to connect DR-Pro S to tape reader and punchers.
- Detailed parameter settings
You can adjust detailed parameter settings including data transmission rate and delay codes to optimize data transmission conditions.
- Automatic program number detection
When receiving data, DR-Pro S automatically detects a program number which follows "0" and record it to an SD card as a file name.
- Simultaneous data transmission
You can transmit all data recorded in an SD card at the same time. It contributes to shorten data transmission time.
|Key Panel||Four-button key panel|
|Interface||Conforming to the EIA RS232C standard
|Start Bit||Fixed to one bit|
|Stop Bit||One or two bits|
|Data Bit||8 bits|
|Power Supply||Nickel-hydride battery||DC6V 600mAh|
|AC Adapter||DC6V 600mA|
|Dimension||Around 90(W) 140(D) 34(H)mm|
|Memory Card||SD card and SDHC card|
About details of the NC program edit software "NEEDS/V," see here.
Official name for Windows® is Microsoft® Windows® Operating System.
Microsoft and Windows are a registered trademark or a trademark of Microsoft Corporation in America and other countries.
Windows® Millennium Edition、Windows® Vista、Windows® 7 are product names of Microsoft Corporation.
Those names are abbreviated as;
Windows Me for Microsoft® Windows® Millennium Edition
Windows Vista for Microsoft® Windows® Vista
Windows 7 for Microsoft® Windows® 7
DR-Pro S Special pack
15：DR-150, DR-Pro series
-**：Marks for a customed cable
Download Brochure and Manual
DR-Pro S can send and receive CNC data with a memory card.
- High speed data transmission
Transmit and receive data at the speed of 38,400bps at most, shortening data transmission time.
- Data transmission with various types of NC machines
Data can be transmitted to/from many kinds of NC machines. DR-PRO can conduct data transmission regardless of the machines' communication methods.
- MS-DOS compatible format
We developed the operating system only for DR-Pro and it lets you register data in the format compatible with MS-DOS. So, data can be directly transmitted to/from a computer through a memory card.
- CNC data transmission
- Data logging
- Memory card storage
- Small and portable
Sold at special internet prices. For details, see here.
- In-house Products
- DC Power Supply
- Rush-starting Loom Controller
- NC Data Recorder
- Jet Loom Controller
- NC Program Edit Software
- Loom Inverter for Inching Movement
- Timing System for Racing Vehicles
- Weft Feeder
- Sensor for Power Source
- Cable Checker "Kanpeki/Wanmei"
- Electrical Device
- Electrical Control Device
- Control Software Development
- Control Device Assembly
- Control Box Production
- Wiring and Trial
- Wire Harness