Cable Checker "Kanpeki/Wanmei"
Kanpeki/Wanmei checks cable conduction (Manual/Auto operation). Kanpeki/Wanmei works stand-alone and with a PC. When Kanpeki/Wanmei is connected to a PC, data on wiring conditions are editable.
Can test up to 104 points. Check correspondence of input and output one-by-one until every correspondence is verified. A connector part has two 50-pin connectors and one 5-pin connector.
- CN-A: 50-pins (A01 to A50)
- CN-B: 50-pins (B01 to B50)
- CN-C: 5-pins (C01 to C04 and common terminal)
With standard extension boards (two sets), Kanpeki/Wanmei can support a connector that has different number of pins and can be used for a jig (Pole numbers: 10, 14, 16, 20, 26, 30, 34, 40, 50). C01 to C04, are used to check a conduction between a shielding wire and a connector case.
You need a conversion jig to connect Kanpeki/Wanmei or extension boards to a targeted cable. if you do not have, we prepare it for you.
Five Test Modes
- Probe Mode
Probe mode is a manual operation mode dedicated for a wiring check. Monitor conductions among 104 pins and connection with a probe common terminal. This mode is employed to check unfastened lead cables.
Image of Probe Mode Connection.
- One-to-one Mode
Check straight cables with up to 50 pins one-to-one. Monitor a conduction between two cables connected on CN-A and CN-B.
Image of One-to-one Mode Connection
- Master／Work Mode
Compare data on wiring conditions stored in Kanpeki/Wanmei with targeted cables. This mode works best at monitoring the same type of cables in large quantities.
Master／Work Mode Connection
- Self-diagnosis Mode
Diagnose Kanpeki/Wanmei itself to find failures.
- PC Mode
・Check a conduction of cables with a PC. Can remotely monitor cable conditions in probe, one-to-one, and master/work modes. Data are checkable on a display, fascilitate monitoring.
・Data including a serial number, name for a blocked area, product and customer name, cable type, comments, pin name, and cable conditions are all editable. Can save data of 10 cables in one file.
・Can generate sequential numbers easily.
PC Mode Connection
Software of Kanpeki/Wanmei
Kuroko, sister device of Kanpeki
Connection monitor Kuroko is a sister device of Kanpeki/Wanmei, and Kuroko can be connected to kanpeki or an expansion board to support visibility of Kanpeki (Kuroko is sold separately from Kanpeki/Wanmei and sold at 7800 Yen. Tax is not included).
Kuroko has high portablility, and you can take it wherever you want.
Kuroko helps you to conduct wiring work more efficiently.
Buy one Kanpeki/Wanmei, get one Kuroko for FREE!
We now present you one Kuroko when you order one Kanpeki/Wanmei on our website! Try it and you will like it! See the details on "Kuroko" here!
|Input and Output Specifications|
|Test Method||All-pin checking|
|Number of Circuits||(For input and output) 104 points
(CN-A: 50, CN-B: 50, CN-C: 4+probe common terminal)
|Test Conditions||Under resistance values of 100Ω
(Should be less than 10 connections/one pin)
|Current||Less than 2.5m A／one pin (Changes according to the number of cable connections)|
|Semi-conductor Detection||Diode: Detect polarity (Can set two diodes in series)
LED: Disabled (Correspondense mode)
|Stand-alone Checking||CN-A: 50P (Hirose HIF)
CN-B: 50P (Hirose HIF)
CN-C: 4P+ probe common terminal (Nichiatsu VHR)
|Checking on PC||B-type USB
(Power source for circuit providable)
|Probe Mode||Manual mode for a wiring check
(CN-A, CN-B, CN-C: 104 points in total)
|One-to-one Mode||One-to-one checking
(Between CN-A and CN-B)
|Master／Work Mode||Comparison checking on 104 points|
|Self-diagnosis Mode||Diagnose Kanpeki/Wanmei itself to find failures|
|PC Mode||Conduction checking on a PC|
|Power Supply (3 ways)|
|Adapter||AC adaptor (Normal voltage: AC100V - 6VDC, 0.5A)|
|USB||5VDC, max.370mA, typ.140mA|
|Battery||6V, 650mAH (Ni-MH)
Operating time: More than 8 hours (When a battery is charged for 24 hours)
|Dimension and Weight|
|Weight||About 1,300g (Including battery)|
You can now try Kanpeki/Wanmei for free.
Kanpeki/Wanmei is your best choice for cable checking.
Download Brochure, Manual, and Software
Software Lisence for "KANPEKI" of The Cable Checker "Kanpeki/Wanmei"
HOKUETSU DENKEN CORPORATION (Our Company, hereafter) permits you to use the software for the cable checker "Kanpeki/Wanmei" (This Software, hereafter) only when you comply with the software license. Please read lisence manual carefully. When you start using this software, you are considered to agree to the software license.
1 Our company has the copyright.
2. Our company will not take any responsibilities for loss and damages by the results of using this software.
3. You shall not analyze this software without permission.
4. This software is subject to change without notice.
5.This software is only for the cable checker "Kanpeki/Wanmei" and a customer only who purchased this product is granted to use a full version of this software (Trial version is downloadable).
*USB driver is needed to connect Kanpeki/Wanmei to a PC.
Download at the link under.
Future Technology Devices International Ltd.
- In-house Products
- DC Power Supply
- Rush-starting Loom Controller
- NC Data Recorder
- Jet Loom Controller
- NC Program Edit Software
- Loom Inverter for Inching Movement
- Timing System for Racing Vehicles
- Weft Feeder
- Sensor for Power Source
- Cable Checker "Kanpeki/Wanmei"
- Electrical Device
- Electrical Control Device
- Control Software Development
- Control Device Assembly
- Control Box Production
- Wiring and Trial
- Wire Harness